Top-Rated HVAC in Ann Arbor, MI

Completed full HVAC system installation including new Bryant furnace and air conditioning unit in residential basement location. During installation, technicians identified a faulty pressure switch that requires replacement. Equipment was successfully installed with proper ductwork connections, gas line hookup, and PVC venting. Pressure switch part needs to be collected from available stock inventory for follow-up service appointment to complete final system commissioning.

Performed comprehensive system inspection and tune-up on residential gas furnace. Completed all required documentation and provided city certification to homeowner upon collection of certification fee. Unit showed normal wear consistent with age, with minor rust present on base panel but all components functioning within acceptable parameters.

Performed comprehensive promotional water heater tune-up on tanked unit located in basement utility area. Inspection revealed system operating within normal parameters with proper connections of copper and PVC supply lines, functional blue shut-off valve, and circulation pump in good working condition. Noted significant brown staining on ceiling insulation above equipment indicating previous water damage or moisture intrusion, though no active leaks were detected during service visit; recommended customer monitor area and address underlying moisture source to prevent future damage.

# HVAC System Installation Completed installation of new air conditioning system with evaporator coil integrated into existing Carrier furnace setup in basement utility area. Installed indoor air handler unit with proper electrical connections using black conduit, positioned above furnace for optimal airflow distribution. Configured white PVC condensate drain lines running vertically alongside equipment to ensure proper moisture removal from cooling operation. On building exterior, mounted and secured condensate drainage piping to wall using metal straps, including proper trap configuration to prevent air infiltration and ensure gravity drainage. Installed vertical PVC conduit for refrigerant line protection and routed all exterior piping in accordance with manufacturer specifications. Connected all electrical components including control box and verified proper voltage supply to new equipment. System tested for proper operation, refrigerant charge verified, and all connections chec

condenser and coil

Successfully installed a 40-gallon natural draft water heater in the basement utility area. The installation included proper copper piping connections, mounting of a blue expansion tank above the unit, and verification of all safety specifications and venting requirements per manufacturer guidelines.

Responded to service call for non-functioning humidifier with gas furnace still operational. Upon inspection, discovered moisture accumulation and potential corrosion on internal ductwork components and humidifier assembly. Examined flexible ductwork in attic space showing debris accumulation and insulation exposure. Inspected air handling unit interior, noting oxidation on metal panels, moisture presence on metallic surfaces, and dust buildup on system components. Documented conditions with photos for records. System assessed and findings reviewed with customer for repair recommendations.

Completed removal and replacement of existing Williams wall furnace unit. Installed new wall furnace in corner alcove location with integrated blower kit for improved air circulation and heating efficiency. Mounted unit securely to wall structure, verified proper electrical connections, and routed power cord along baseboard for clean installation appearance. Confirmed exterior exhaust vent is properly sealed and functioning, with chrome vent cover mounted flush to exterior siding. Tested unit operation including ignition sequence, blower motor function, and thermostat response. Verified proper combustion air intake and exhaust ventilation. All safety controls and limit switches checked and operational. Unit heating effectively and cycling normally upon departure.

Completed full HVAC system installation including new Bryant 2-ton air conditioning condensing unit, furnace, and air purification system. Unit installed on concrete pad with proper electrical disconnect, refrigerant lines, and PVC condensate drainage system with trap configuration. Performed complete tuneup on existing hot water tank while on site to ensure optimal performance and system integration.

Completed spring AC tune-up on 1-year-old Lennox unit. Outdoor condenser showed heavy accumulation of dirt, leaves, and organic debris on top mesh grill and surrounding area. Performed comprehensive maintenance including cleaning condenser coil, inspecting refrigerant lines and connections, checking electrical components, and verifying proper system operation. All copper piping, brass fittings, and flexible conduit connections were inspected and found secure. System tested and confirmed working properly with no issues identified.

Completed routine HVAC maintenance tune-up on a 6-year-old furnace system that was operating properly. Performed standard inspection and preventative maintenance procedures. Documented existing copper piping configuration with T-joint fittings and compression connectors, noting foam pipe insulation in place. Observed significant corrosion and material degradation on metal component near pipe junction, indicating long-term moisture exposure that will require monitoring or future repair consideration. System remains operational following tune-up service.

Successfully completed a full HVAC system installation including a new furnace, air conditioning unit, and whole-home humidifier. The outdoor condensing unit was professionally mounted on a gravel pad against the building exterior with proper clearances, and a PVC condensate drain line was installed and routed to ensure proper drainage. All equipment was installed to manufacturer specifications, labeled appropriately with model and manufacturing date information, and is fully operational.

Completed full HVAC system installation in residential basement utility room, including new Bryant 96% AFUE gas furnace (Model 9DSX96G0N14A) and air conditioning system. Installed furnace with proper PVC venting configuration, connected air handler with supply and return ductwork, and integrated all electrical connections and gas lines per manufacturer specifications and local code requirements.

Performed comprehensive water heater tune-up on residential tanked unit located in basement utility area. Conducted thorough inspection of all plumbing connections, including inlet and outlet copper piping, temperature and pressure relief valve, and associated brass fittings at base of unit. Verified proper operation of venting system with metal flue pipe connection to ceiling. Inspected manufacturer labels and specification plates for compliance verification. Examined condition of surrounding plumbing infrastructure including PEX distribution lines mounted to pegboard walls and confirmed adequate clearances around unit per code requirements. All components found to be functioning within normal parameters. Documented equipment condition with photographic records showing water heater installation, mechanical room layout, and plumbing configuration for service history reference.

Completed comprehensive tune-up service on 2022 air conditioning system and boiler unit. Performed full system inspection of furnace/air handler assembly, verified electrical connections at junction box, and assessed ductwork condition in attic space. Noted 6-inch flexible aluminum duct showing signs of deterioration with compromised foil covering requiring future attention, though system remains operational at this time.

Responded to service call for boiler that would not shut off. Upon inspection, found significant corrosion and verdigris buildup on brass valve components and pipe fittings throughout the boiler system. Identified faulty zone valve with corroded electrical connections and compromised mechanical operation preventing proper system shutdown. Evaluated multiple copper pipe branches with gate valves controlling different heating zones. Noted aging infrastructure with varying degrees of oxidation on copper piping and fittings. Recommended replacement of corroded valve assembly and affected electrical components to restore proper boiler cycling and prevent continuous operation.

Installed a new Bradford White gas-fired water heater in basement utility area, including all necessary plumbing connections with copper piping and brass fittings at the unit's inlet and outlet. Configured proper venting system with metallic exhaust pipe, installed pressure relief valve with discharge piping, and integrated pressure tank into the system. Additionally, ran new gas piping from existing supply to accommodate outdoor grill installation, ensuring all connections meet code requirements and proper gas flow to both appliances.

Completed standard water heater tune-up on residential tanked unit located in utility closet. Performed comprehensive inspection of all plumbing connections, pressure relief valve testing, and verified proper operation of gas supply lines and venting system. Flushed sediment from tank bottom, inspected anode rod condition, tested temperature and pressure settings for optimal performance, and confirmed all PVC condensate and exhaust lines were properly secured and functioning. Unit operating within normal parameters upon completion of maintenance service.

Relocated Coleman brand air conditioning condenser unit to exterior corner of building. Existing electrical wiring was sufficient length for new location; installed new refrigerant lineset with filter dryer to accommodate repositioned unit. Unit mounted on new pad with proper clearance from building, electrical disconnect box repositioned and conduit rerouted to new location. System tested and operational upon completion.

Conducted site assessment and provided estimate for gas line installation to outdoor grill location on residential deck. This estimate is in addition to previously quoted standard water heater replacement, with both projects to be coordinated for the property.